Showing posts with label amp. Show all posts
Showing posts with label amp. Show all posts

7/01/2012

Marshall MG250 DFX Stereo Combo Amplifier Review

Marshall MG250 DFX Stereo Combo Amplifier
Average Reviews:

(More customer reviews)
I bought this amp at a bargain price and thought that I may resell it. I'm very fussy about amps as all I've had until the last year or so were pre CBS Fenders. A Princeton Reverb, A Deluxe Reverb and a Twin Reverb with EV SRO speakers. Well, this Marshall can't be a Fender vintage tube amp but it is a really decent amp. And the cost of tube amps is nuts. I decided to keep this amp. It has some nice clean sounds, which is what I'm after. I also use a Fender solid state and I find that these amps sound pretty good. Not like the solid state amps of the 60s. Standell solid states or the Silvertone 6 x 10"? :

Click Here to see more reviews about: Marshall MG250 DFX Stereo Combo Amplifier

The MG250DFX is a 2-channel stereo amp with special features such as FDD (Frequency Dependent Dampening), CD ins, plus emulated line out, and emulated headphone jacks. It features digital effects including reverb, delay, chorus, and flange. With 100W (2 x 50W) and 2 - 12" Celestion speakers, this is a fully gig-capable amp, and it retains all the features that make it great for practice, too.

Buy Now

Click here for more information about Marshall MG250 DFX Stereo Combo Amplifier

Read More...

6/16/2012

Fender Hot Rod Deville 212 Tube Combo Amp Review

Fender Hot Rod Deville 212 Tube Combo Amp
Average Reviews:

(More customer reviews)
The Fender Deville HotRod 212 is an excellent amplifier. With a few simple modifications it can be voiced to be superior to most amplifiers produced by Fender and other makers. The stock amp is very loud and a bit hard to control in smaller venues. Also the reverb is slightly thin. Finally, the voicing of the drive and more drive channels is a bit aggressive. After the following mods found on [...] the amp is stunning. Here are the mods I performed.
- Replace the stock master volume with an audio-taper is the best way to fix the oversensitive Master (A250KÙ). Your tech will need to bypass resistor R45 with a straight wire to raise the gain level of the master to match the volume channel.
- Replace the V1 and V2 12ax7 tubes with 12at7 tubes. This will improve the headroom and tame the drive and more drive channels. The sound becomes richer and competes head on with pricer Fender and expensive competitor amps. If you like a bit more punch that is still bluesy try keeping a 12AX7 in V2
-Replace V3 with a 12au7 or a 12at7. This slightly reduces gain, not power, in both channels and improves headroom making the amp more suited to blues and jazz. The amp will still rock and play just as loud. These tube changessweeten the sound of the clean and distortion channels.
- Cut out resistor R103. This is part of a treble boosting circuit in the reverb section possibly added by Fender to help sell the amps in noisy music stores. This simple mod makes the reverb very rich and superior to many amps on the market including many of Fender's best.
If you get a Deville Hot Rod, read Justin Holton's site carefully. These amps have VERY HIGH VOLTAGE and the volume pot and resistor removal require knowledge and safety steps. DO NOT try this in less you are technically trained. A tech can easily make these changes for you. If you proceed yourself you must be trained and take proper precautions as described on Justin's site. Such changes will VOID the warranty so this is best done on used gear.
The amp stock is excellent and very well made. These changes take to top tier performance.


Click Here to see more reviews about: Fender Hot Rod Deville 212 Tube Combo Amp

Fender Hot Rod Deville

Buy Now

Click here for more information about Fender Hot Rod Deville 212 Tube Combo Amp

Read More...

6/13/2012

Bugera 333XL 120-Watt 3-Channel Valve Amplifier Head with Reverb Review

Bugera 333XL 120-Watt 3-Channel Valve Amplifier Head with Reverb
Average Reviews:

(More customer reviews)
I bought this amp a few months ago, and let me tell you it is a tone machine!! I'm not in a band, or a professional musician, just a regular guy searching for that tone. This amp is everything it claims. Great sound, awesome power, incredible gain and tone at a reasonable price. I have always wanted an all tube half stack, but just couldn't justify $2K for it. I also purchased the Bugera slant cab, after playing the 333XL through my Marshall AVT112 cab. The speakers in the Bugera cab are very thin, tinny sounding, but I fixed that just recently(see review of the Bugera 412 slant cab).
I would not hesitate to buy another Bugera if warranted to. These amps are a steal for what they are, and their incredible tone!!

Click Here to see more reviews about: Bugera 333XL 120-Watt 3-Channel Valve Amplifier Head with Reverb

Boutique-Style 120-Watt 3-Channel Valve Amplifier Head with Reverb

Buy NowGet 32% OFF

Click here for more information about Bugera 333XL 120-Watt 3-Channel Valve Amplifier Head with Reverb

Read More...

6/09/2012

Bugera 1960 Classic 150-Watt Hi-Gain Valve Amplifier Head Review

Bugera 1960 Classic 150-Watt Hi-Gain Valve Amplifier Head
Average Reviews:

(More customer reviews)
I did a lot of research (or as much as possible) on this amp. First of all, I'm 32 and play all kinds of tones. I'm current with all kinds of music, and don't just play bbq blues. I've been looking for an affordable all tube amp for some time that didn't have all kinds of doo-dads and modelers, etc. I've owned a '78 50watt JMP, '73 Sunn Model T, 70's Fender Twin, Orange AD30, as well as some solid state amps when i was first getting into guitar.....So i'm familiar with tube tone and good vs. bad. The only thing this AMP can't do is nu-metal...but that's a good thing. you can hook up a tone sucking distortion pedal if you must, but don't waste all this warmth. For someone who plays at low volumes, this may not be the amp for you. this amp is plenty loud, and sounds better the louder it's turned up. It has a grindy overdrive and distortion as opposed to a smooth or fuzz type. I personally love this, and is what i look for. Bridging the high and low channel is the way to go, but you'll have to crank it to get it to break up...so again, if you don't like it loud, get an amp that has a master volume. The high channel will drive the pre-amp for tone, and the low will drive the power tubes to get its tone. not the most versital amp but if you like it pure, this is a great competitor in the tube amp tone world. I perfer it to many of the amps that were $1,000 more.

Click Here to see more reviews about: Bugera 1960 Classic 150-Watt Hi-Gain Valve Amplifier Head

Classic 150-Watt Hi-Gain Valve Amplifier Head

Buy NowGet 32% OFF

Click here for more information about Bugera 1960 Classic 150-Watt Hi-Gain Valve Amplifier Head

Read More...

6/07/2012

QSC GX3 Stereo Power Amplifier Review

QSC GX3 Stereo Power Amplifier
Average Reviews:

(More customer reviews)
I started looking around for a performance power amp that was in between crown and Behringer. Now while I consider Crown the holy grail of power amps, I didn't feel like spending the cash for the Harley-Davidson of power amps. So when looking, I actually took a look at parts express and their most popular power amps. To me, the majority of the people that visit that site have their head screwed on straight and care about quality products. While a lot of the reviews showed promise for Behringer, my cousin and I currently employ a tube based preamp in my studio, and while it worked flawlessly in the beginning, all the pot's on my preamp are now fuzzy and buzzy. His preamp sucked from day one, buzzing at 60Hz, requiring post process filtering which saps the nuances out of the recording. To sum up my opposition to Behringer, I didn't feel like getting a product that worked well for a year or two, though I just bought a Behringer 8-channel mixer to go with it ($60 and not regretting it yet, but we'll see)
Hooking it up to my 6.5" jbl studio s26-ii's, I was blown away by its punch and clarity. Mind you, its normally being driven by an 80W/ch Onkyo (0.08%THD). The speakers had more dynamic to the sound, and it was absolutely fantastic. I had done this while I awaited the arrival of my MTX PA speakers.
I bought a pair of MTX TP2400 to go along with it. They are definitely not the greatest speaker out there, but they put out the high SPL sound I was looking for in a live performance. The amplifier drives them pretty well, though I cant help but be slightly disappointed with the result. I am confident that the amp is not the culprit though due to how well it has driven my other smaller studio speakers.
I think these cheap PA speakers really show the beauty of the amp though, Its speaker/clipping protection made the music stay at uninterrupted high levels. The other great thing is the 6 year transferable warranty. While I don't really care too much about warranties, Behringer's abysmal 1 year warranty pushed me over to QSC. That's pretty much saying what I think about my current products, they know its too risky to warranty a product longer than a year.
I hope you find this info useful, because these guys deserve every sale they get.

Click Here to see more reviews about: QSC GX3 Stereo Power Amplifier

The QSC GX3 amplifier is ideal for professional entertainers who require maximum performance and portability on a limited budget. QSC designers, headed by Pat Quilter, have optimized output and appearance while reducing raw material cost and weight. It's all here - dramatic styling, easy hookup and adjustments, excellent audio quality and QSC reliability. QSC GX3 Features Power levels matched to the most popular speakers used by entertainers Optimized for maximum real-world headroom into 4 Ohm and 8 Ohm speaker systems Inputs: XLR, 1/4-inch TRS and phono input connectors for compatibility with any source Outputs: Speakon combo accepts, 1/4-inch (TS) plugs or Speakon 2-pole and 4-pole plugs (connects 2 poles only). Binding posts support all other speaker wiring systems. Minimum depth chassis (10.1 inches/257 mm) fits in compact, inexpensive effects racks Lightweight - less than 26 lbs (12.5 kg) Detented gain controls for precise settingand matching of sensitivity GuardRail automatically protects the amplifier and loudspeakers from damage due to temperature rise or overdrive without shutting down the show Front panel LEDs monitor Power, Signaland Clipping Subwoofer/Satellite crossover built-inGX Entertainer GX amplifiers deliver just the right amount of power to the most popular speakers used by entertainers. Most loudspeaker manufacturers recommend an amplifier with power output equal to the speaker's Program (Music) Power rating or two times (2 x) the Continuous (RMS) Power rating. The GX3 is ideal for speakers in the 300 watt (Program) range.The GX3 supplies maximum possible power to 4 ohm and 8 ohm loads. Technical Notes The GX3 uses the latest evolution of the QSC Grounded Collector output system, for optimum cooling of the critical power transistors. A true

Buy NowGet 25% OFF

Click here for more information about QSC GX3 Stereo Power Amplifier

Read More...

Behringer EPX2000 Professional 2000-Watt Light Weight Stereo Power Amplifier with Atr (Accelerated Transient Response) Technology Review

Behringer EPX2000 Professional 2000-Watt Light Weight Stereo Power Amplifier with Atr (Accelerated Transient Response) Technology
Average Reviews:

(More customer reviews)
After thorough research on multiple websites I determined that the Behringer EPX200 was the right amp for my situation. The applied situation for this amplifier is for a fraternity house sound system. So, I emphasize the word rugged in the title, haha. It's been almost a month now and this amp is put through its paces multiple times throughout the week. It's powering two Nady 500 watt speakers and they sound great. This amp puts out plenty of power, and the limiter switch on the back is great because it keeps people from doing harm to the amp or the speakers who don't know how to use it. Seriously, even in a large room, this amp pumps out the sound.

Click Here to see more reviews about: Behringer EPX2000 Professional 2000-Watt Light Weight Stereo Power Amplifier with Atr (Accelerated Transient Response) Technology

Professional 2000-Watt Light Weight Stereo Power Amplifier with ATR (Accelerated Transient Response) Technology

Buy NowGet 50% OFF

Click here for more information about Behringer EPX2000 Professional 2000-Watt Light Weight Stereo Power Amplifier with Atr (Accelerated Transient Response) Technology

Read More...

6/05/2012

Marshall AS100D 2x8 Acoustic Combo Amp Review

Marshall AS100D 2x8 Acoustic Combo Amp
Average Reviews:

(More customer reviews)
Finally, I've found an amp that does what I want it to. Great sound, clear and LOUD. Reverb could be better, but I sometimes use separate effects. Now here was the shocker: I hooked up my electic guit and PODxt, expecting the same crappy sound I've always gotten through acoustic amps (I've tried 5 different brands/models). JIMINY CRICKET what a fantastic sound with this amp, with an electric guitar thru the POD. I'm in HOG HEAVEN. Now, I suppose purists would scoff, but I'm into DRAMA not "multiple condenser mic" purity. All I can say is, after YEARS of flopping around trying to get the right sound at a human price, this wonderful machine does it all for me. At this price, I don't see how anyone could be disappointed.

Click Here to see more reviews about: Marshall AS100D 2x8 Acoustic Combo Amp

This Marshall AS100D Acoustic Combo Amp is the one to have. Specially designed for use with a variety of acoustic instruments with or without pickups. Its four channels give you the flexibility to handle piezo transducers or magnetic pickups, a mic for vocals or instruments, and external audio equipment via a phono input channel. Channels 1 and 2 have separate EQ and level controls but also may be linked. 2x50W stereo power gives you plenty of oomph for stage performance, and a balanced line out allows direct connection to a PA. The Marshall amp has a built-in digital reverb, delay, and chorus that add dimension to your sound, and a balanced parallel effects loop with level is included. Anti-feedback controls include a phase switch and notch filters for each channel with selectable extra notch depth for channels 1 and 2.

Buy Now

Click here for more information about Marshall AS100D 2x8 Acoustic Combo Amp

Read More...

6/04/2012

Peavey Power Amp 2 Rack 2040W Pr Ch @4OH Review

Peavey Power Amp 2 Rack 2040W Pr Ch @4OH
Average Reviews:

(More customer reviews)
The Peavey CS 4080Hz is a terrific power amp that will provide clean power and plenty of headroom. I run two of these actually in my PA...one to drive a pair of Yamaha C215V mains and another for monitor/subwoofer duty. It includes Peavey's DDT (Distortion Detection Technology) which will lower the volume when it detects a clipped waveform...but in my experience, the 4080Hz provides so much headroom that unless you set your gain stages all out of whack you're not likely to need the DDT (although it's nice to know it's there). I recently ran sound at an outdoor fundraiser...only had the 4080's turned up halfway and I could hear crystal clear sound a block and half down the street. I highly recommend this amp...they are reliable, powerful and a worthy aire to the legendary Commercial Series amplifiers Peavey built in the 70's.

Click Here to see more reviews about: Peavey Power Amp 2 Rack 2040W Pr Ch @4OH

Building on the reputation of the world-famous Peavey CS® 800, which conquered the power amp market in the 1970s, the CS® Series is the global standard bearer for workhorse reliability. Over the years, these amps have benefited from some of Peavey's most popular audio innovations, including our exclusive DDTTM compression/anti-clipping protection. With its 2 RU design and power points up to 4080 watts, this latest evolution of the CS® Series is leaner, louder and lighter than ever.

Buy NowGet 36% OFF

Click here for more information about Peavey Power Amp 2 Rack 2040W Pr Ch @4OH

Read More...

QSC GX5 Stereo Power Amplifier Review

QSC GX5 Stereo Power Amplifier
Average Reviews:

(More customer reviews)
I bought the QSC GX5 stereo amplifier for use in my band's practice studio. We previously used a Mackie mixer/amp setup and we recently bought an Allen & Heath mixer along with the QSC Amp. We've gone from a little noisy system to an absolutely silent (no hiss, no noise) system even when turned all the way up. It's nice! We A/B'd the amps and while the Mackie is rated to have more power, the QSC is clearly punchier and so much cleaner. I can't say enough about how nice this amp is. I've owned Crown, Crest and Yamaha amps as well and none of them were cleaner than this one.
As for durability, it's still new BUT QSC is offering a 6 year warranty for free on this model (until March 09) so I can't imagine they would do this if these amps were a service problem.
Oh and it looks great in my rack. I read somewhere that the amp is noisy when the cooling fans get going. Knowing this, I cranked the amp full and ran a punchy CD through the mixer full blast (no distortion!) and waited while the amp warmed up. After it reached operating temperature, the fan(s) indeed came on but by no means were they "loud." If I had this amp in a recording studio, I would have the amp in a soundproof room or enclosure as I suppose the fan could be audible during very quiet recording sessions. On the other hand, it is reassuring that I know the fans are indeed working, keeping the rails cool. For live sound, it just isn't a real issue.
Now I'm considering getting another QSC for a monitor amp. I heartily recommend this amplifier.


Click Here to see more reviews about: QSC GX5 Stereo Power Amplifier

The QSC GX5 amplifier is ideal for professional entertainers who require maximum performance and portability on a limited budget. QSC designers, headed by Pat Quilter, have optimized output and appearance while reducing raw material cost and weight. It's all here - dramatic styling, easy hookup and adjustments, excellent audio quality and QSC reliability. QSC GX5 Features Power levels matched to the most popular speakers used by entertainers Optimized for maximum real-world headroom into 4 Ohm and 8 Ohm speaker systems Inputs: XLR, 1/4-inch TRS and phono input connectors for compatibility with any source Outputs: Speakon combo accepts, 1/4-inch (TS) plugs or Speakon 2-pole and 4-pole plugs (connects 2 poles only). Binding posts support all other speaker wiring systems. Minimum depth chassis (10.1 inches/257 mm) fits in compact, inexpensive effects racks Lightweight - less than 26 lbs (12.5 kg) Detented gain controls for precise settingand matching of sensitivity GuardRail automatically protects the amplifier and loudspeakers from damage due to temperature rise or overdrive without shutting down the show Front panel LEDs monitor Power, Signaland Clipping Subwoofer/Satellite crossover built-inGX Entertainer GX amplifiers deliver just the right amount of power to the most popular speakers used by entertainers. Most loudspeaker manufacturers recommend an amplifier with power output equal to the speaker's Program (Music) Power rating or two times (2 x) the Continuous (RMS) Power rating. The GX5 supplies maximum possible power to 4 ohm and 8 ohm loads. Owners of popular 4 ohm loudspeakers (dual-woofer, two-way models and many subwoofers) will find the 700 watt (4 ohm) power of the GX5 an ideal match. Technical Notes A true Class B biasing system combines maximum

Buy NowGet 20% OFF

Click here for more information about QSC GX5 Stereo Power Amplifier

Read More...

6/03/2012

Gallien-Krueger 1001 RB-II Bi-Amp Bass Amplifier Review

Gallien-Krueger 1001 RB-II Bi-Amp Bass Amplifier
Average Reviews:

(More customer reviews)
As with most bass players, I started with economy gear. I very quickly learned how dramatic a difference high-end gear can make in the quality of your sound (when I upgraded to a Gallien-Krueger 115RBH Bass Guitar Cabinet (400 Watt)). The clarity of the sound when compared to my first cabinet ( Hartke VX410 Bass Guitar Amplifier 4x10 Cabinet, 400 watts) was astonishing! I knew the same would be true for the amplifier, and this was confirmed when I upgraded from the my first amp (Hartke 3500C Bass Guitar Amplifier Head, 350 Watts) to this Gallien-Kruger 1001RB(II). It has amazing power, clarity, and flexibility of tone (which becomes increasingly important as you start to play with other musicians).
I feel like I have discovered the Holy Grail of Bass Amplifiers! Thank you Bob Gallien, for your original vision, and for all your many years of commitment to excellent and innovation in developing and producing quality bass gear beyond the call of duty. You have made the world a better place for musicians as well as all those who listen to music! I hope to eventually add the (Gallien-Krueger 410RBH/8 Bass Guitar Cabinet (800 Watt)) to the rig (when I start playing larger venues).

Click Here to see more reviews about: Gallien-Krueger 1001 RB-II Bi-Amp Bass Amplifier

700 watt bass amp with 50 watt horn amp

Buy NowGet 30% OFF

Click here for more information about Gallien-Krueger 1001 RB-II Bi-Amp Bass Amplifier

Read More...

5/31/2012

Line 6 Spider Valve HD100 Review

Line 6 Spider Valve HD100
Average Reviews:

(More customer reviews)
This sucker sounds really great. And it's true what they say about tube amps. You aren't really hearing it unless you crank it. I cranked it, and it was the greatest thing I've ever heard (I played a metal chord, then turned it from super loud to very low, and I could progressively hear the tone go from amazingly thick and rich, to crackly and thin. so only buy this if you plan on playing it LOUD). Put it on the Metal or Insane settings, and it's just nuts. However, it broke the next day, so I had to send it off for repair to a "local" service center (where Line 6 made me pay 30 bucks to ship. thanks L6). It's been over a month and they finally got around to checking it out. They told me the tubes were faulty. So great. Now they say another 2 weeks to order new tubes and test to see if there are any other problems. Nice work, Line 6. BTW, my POD X3's headphone jack only outputs a MONO signal now. How great is that? Talk about quality! (the presets suck too btw. no one uses those. and you can't customize them like you can on the POD X3, but thankfully, you don't need them. the main channel knob has all you need!!)
Other than that, this amp sounds AMAZING. A shame about the faulty tubes in my unit, but I hope when I get it back, it will last longer than a few minutes of it cranked. And no, not crazy cranked, just normal cranked.
The matching cab sounds amazing btw.

Click Here to see more reviews about: Line 6 Spider Valve HD100

Spider Valve fuses the versatility of amp and effects modeling with the performance and feel of a world-class tube amplifier. Combining award-winning Line 6 modeling technology with a genuine tube amplifier designed by legendary amp designer Reinhold Bogner, Spider Valve delivers unmatched performance, responsiveness and tonal flexibility on the stage and in the studio.

Buy NowGet 29% OFF

Click here for more information about Line 6 Spider Valve HD100

Read More...

Line 6 Spider Valve 212 Review

Line 6 Spider Valve 212
Average Reviews:

(More customer reviews)
I've been playing guitar for about 16 years, but I'll admit I know next to nothing about amps. I know what are generally considered to be good amps (Bogner, Marshall, Mesa/Boogie, etc.), but I couldn't look at the specs on an amp and tell you if it was any good.
After a little research, I came to the conclusion that I wanted a tube combo amp, something suitable for gigging or for practicing in the bedroom, that would give me a good variety of tones. (I like to play a wide range of music, from classic rock to metal and fusion, and bands I play with usually do covers.) I went down to Guitar Center with this in mind, and one of the salespeople pointed me to the Line 6 Spider Valve 212.
I plugged in an Ernie Ball Music Man JP6 (the same guitar I have at home) and immediately fell in love with the tone. You can see the specs for this amp a little farther up on the page, so I'll just talk about what matters: this amp sounds great. Plug in a good guitar with some good pickups, and you can dial in pretty much any tone you're after. Crank it up loud, and the tube power really shines. More than a dozen amp models (two choices for each individual setting on the dial) give you a wide variety of possible sounds. You'll likely hit on one or two models that you prefer, but even within a single setting you can dial in an impressive variety of tones.
I wasn't thrilled with the clean setting, but all I had to do get the clean sound I was after was to turn down the gain on the crunch setting, add a tiny bit of tape delay and some reverb, and there it was: my perfect clean tone. I've settled on the metal modeler (amber LED) for most of my high-gain tones, but I've only had it for about a week. I'm sure I'll find all kinds of great tones on different settings.
The one complaint I have about this amp is about the effects. They are limited, as you might expect with onboard effects, but the modulation effects in particular are practically unusable. The chorus and flanger are combined on the same dial for some reason, but all I really hear when I turn it on is a flanger, which is far too overpowering besides not being tweakable. A shame, since chorus is the only modulation effect I regularly use. The phaser and tremolo are okay, but I rarely use either and haven't experimented with them. The delay, on the other hand, is very usable, and I'm glad it got its own dial with three different flavors. The tap button for setting the tempo is essential and makes the onboard delay all most guitarists will need. The reverb is decent but a little overpowering at anywhere past about 11:00 on the dial.
Some other cool things about this amp include a built-in noise gate (just hold the tap button while turning the reverb dial past noon to activate it), distortion boost (hold the tap button while turning the drive dial past noon), and a tuner (hold the tap button in until the preset indicator switches to tuner mode). You can also save all your favorite settings as presets, easily navigable with a Line 6 FBV Express or Shortboard foot switch. (I strongly recommend spending the extra $100 on an FBV Express, though $230 for a Shortboard seems a little steep.)
(A quick side not about presets: the amp comes with 400+ presets, including 9 user-programmable banks with 4 patches each, totaling 36 programmable channels. You can't overwrite any of the artist or song presets. The presets are mostly decent at best, but they're a good starting point for tweaking. The amp does include a port for a PODxt, which you can also control with your FBV foot switch, and though I've never used one I'm sure it has plenty of programmable patches, so you aren't exactly limited to the amp's channels or presets.)
All in all, this amp sounds great with a huge variety of possible tones and options that will suit the needs of most guitarists playing in cover bands or just having fun at home. No, it can't compete with a Mesa Dual Rectifier half stack, but for a tube combo amp at well under $1,000, it can't be beat. Did I mention how loud this thing gets? I haven't been able to crank it past 10:00 on the master volume yet. I can't imagine anyone would ever need to go past 1:00, even at gigs. It's a seriously loud 40 watts.

Click Here to see more reviews about: Line 6 Spider Valve 212

Spider Valve fuses the versatility of amp and effects modeling with the performance and feel of a world-class tube amplifier. Combining award-winning Line 6 modeling technology with a genuine tube amplifier designed by legendary amp designer Reinhold Bogner, Spider Valve delivers unmatched performance, responsiveness and tonal flexibility on the stage and in the studio.

Buy NowGet 29% OFF

Click here for more information about Line 6 Spider Valve 212

Read More...

5/19/2012

Crown XLS2500 Power Amplifier with integrated PureBand Crossover System and PeakX Limiters Review

Crown XLS2500 Power Amplifier with integrated PureBand Crossover System and PeakX Limiters
Average Reviews:

(More customer reviews)
I have 4 of these stacked in a case and can actually carry them by myself. The class d amp is amazing and the system performs wonderfully. Navigating the menus is simple. Can't go wrong.

Click Here to see more reviews about: Crown XLS2500 Power Amplifier with integrated PureBand Crossover System and PeakX Limiters

Crown's XLS Series amplifiers define the standard for portable PA systems with unmatched performance, technology and affordability. Its advantageous flexibility includes multiple inputs so you can plug in anything and play anywhere, along with several system setup configurations. The integrated crossovers and switch-mode power supply produce superior sound, and Peakx' limiters protect your speakers. Weighing less than 12 pounds, compared to 40 pounds for its competitors, it's much easier to set up and move from show to show. Simply put, the XLS is most reliable, versatile, efficient amp available today.

Buy NowGet 45% OFF

Click here for more information about Crown XLS2500 Power Amplifier with integrated PureBand Crossover System and PeakX Limiters

Read More...

Line 6 Vetta II Combo Amp Review

Line 6 Vetta II Combo Amp
Average Reviews:

(More customer reviews)
This amp has servered me well, I still use it extensively for live performances as well as recording. I bought it back in 2004 and it's still going strong.
The paragraph below is basically the same review I posted on Musicians Friend back in 2006.
This amp has all the features I've ever wanted and a lot more. If you're a mad scientist type that likes experimenting, then you will love this amp. If you're someone that doesn't like messing around with a lot of knobs and settings, then this is not the amp for you, buy a Fender twin or a Marshall half and be done with it. While the Vetta II alone offers a lot of capabilities I do recommend the FBV floorboard and Variax guitar if your budget permits. The value of being able change your amp and guitar models with a single click of a footswitch is worth the price of admission IMHO. Before I had the Vetta II and Variax I can't tell you how many times I wished for this capability while switching guitars between songs at a gig. The only issue I've had with this amp is it's susceptibility to power surges. It used to reset itself on me during rehearsals but since then, I've always plugged it into a surge protector and it's never reset on me during a gig.

Click Here to see more reviews about: Line 6 Vetta II Combo Amp

Vetta II is the latest evolution of Line 6's flagship Vetta amplifier family.Inside Vetta II lives a virtual collection of 80 sought-after vintage and modern amps and cabs, over 50 stompbox and studio rack effects, and 4 classic mic/cabinet setups.At the touch of a single button, Vetta II can deliver two independent amp and effects paths at once, giving you the creative freedom to build incredibly detailed tones.At home, on stage, or in the studio, Vetta II features XLR balanced direct outs, AES/EBU and S/PDIF 24-bit/96KHz digital inputs and outputs, and A.I.R. II mic/speaker simulation.Vetta II is loaded with a pair of custom 12" Celestion speakers driven by a 150-watt stereo power section, and includes a direct digital Variax Modeling Guitar input that seamlessly integrates Variax's collection of guitars with Vetta II's collection of amps, cabs, and effects. Add an FBV pedal board, and this entire setup can be transformed into virtually any rig with just the press of a footswitch. And now there's even more!Download the FREE Vetta II V2.5 Update and get an all-new collection of Wah models, expression pedal controlled Pitch Bending, 6 new Amp Models, a dedicated Solo Boost function, Tuner enhancements, Tap Tempo that syncs to MIDI clock, plus much more.

Buy Now

Click here for more information about Line 6 Vetta II Combo Amp

Read More...

5/12/2012

Warmenfat Micro Amplifier Review

Warmenfat Micro Amplifier
Average Reviews:

(More customer reviews)
I run Weston House Recording, a tiny recording studio out of my small home in Orangevale, CA; just on the edge of Sacramento.
On occasion, I have gear go down and usually travel to the San Francisco Bay Area for repair. Within the past year, I ran into the Rainbow Electronics repair shop, not more than 10 miles from me. Funny thing is that it they've been there for 20 years!
John McCormack owns and runs Rainbow Electronics along with his wife. From the moment we met, we became instant friends; with me being intrigued with all that he does and he with all that I do.
Out of one of our numerous conversations, he introduced me to his Warmenfat project. Of course, me being one who is always looking for high-quality gear at reasonable prices from not-so-known very small gear manufacturers, there was no choice but for me to buy one so that I could try it out over a long period of time in my studio.
I've been using the Warmenfat for almost a year now. It seems I pull it out whenever nothing else seems to work. In particular, it's great when electric guitar players come into the studio and want to go directly out of their analog or digital pedals or when they want to use their little practice amps with all their digital modeling. These "budget" pieces usually have good tone but for whatever reason, they rarely seem big and 3-dimensional.
I've found that if I run the Warmenfat inline some place in the signal-chain, I can dial-in just the right type and amount of tube character I need and get some life out of these units. I'd imagine it's from all the good and not-so-good natural characteristics in the high-quality tubes and transformer in the Warmenfat; not to mention the excellent circuit designing and product manufacturing.
There are endless possibilities with the Warmenfat. I haven't had the opportunity yet, as there's not really ever any money in paying artists budgets for experimentation, but I look forward in my own projects to try patching in the Warmenfat in various places, such as big electric guitar amp's effects loops, bass tracks, vocal tracks, FX buses, and so many other things!
Weston Ray

Click Here to see more reviews about: Warmenfat Micro Amplifier

The Warmenfat Micro Amp is a versatile compact class A pure tube amplifier. Designed for lead guitar, bass guitar, keyboards, microphone pre amp, or as an effects processor. It can also be used anywhere to add tube tone. The 2 watt single ended tube output stage can easily drive a lead guitar cabinet to a wonderfully over driven tube crunch tone at practice volume level! Used in an effects loop, it can add tube warmth to solid state modeling amps. Old school tube amplifiers can benefit from its ability to add massive overdrive, British style tone crunch without "hot rodding" or modifying the vintage old amp. Used as tube microphone preamplifier, the Warmenfat Micro Amp offers world class performance. The aerospace derived low noise Ohmite metal film resistors and the Wima polypropylene capacitors allow the Warmenfat to reproduce with a clarity and natural warmth that out performs microphone pre amps costing thousands of dollars. Using multiple Warmenfats cascaded can result in awesome crunch or even be used with spring reverb unit for the ultimate pure tube stereo chorus sound.The Warmenfat Micro Amps versatility limits it usefulness only to the imagination of its owner.

Buy Now

Click here for more information about Warmenfat Micro Amplifier

Read More...

Epiphone Blues Custom Combo Amplifier, 15/30W, Tube 2x12" Speaker Review

Epiphone Blues Custom Combo Amplifier, 15/30W, Tube 2x12 Speaker
Average Reviews:

(More customer reviews)
I have owned and gigged with this amp for nearly 2 years. I play thru it exclusively, if I am even using an amp. I have a custom made guitar, so I can't help anyone achieve a well known tone. Sorry. But I can say that it is fairly easy to find your very own sound with this amp. It has alot of tone shaping choices in the form of the eq, and a switch that also acts as a frequency boost in a way. It is a switch that can make the 3 different bands of the eq act independently of each other, or not. For example, on windows media player, you can set the eq sliders where if u move one of them, the other frequencies are going to pull up a little all around that slider. Same highly generalized theory. Kinda. This amplifier has a great tube tone, and you can get a "pop" to some bass notes. Kinda funky. It is solid. Absolutely. And will get very loud. I've never gigged anywhere where I could even think of turning this up past halfway, on the 15w class A setting.
It is a trebly amp. And I play a trebly maple guitar. But I just turn the highs down a good bit on the amp, and roll a little tone off my pickups, i have an even sounding tone. The overdrive channel is fairly good, but it has always been way too trebly, even while playing a Black Beauty in the rythm position. Soooo, I would suggest either changing all the tubes, (they had to cut cost somewhere), or use your own overdrive. If u turn this amp up on the clean channel, it will have a very nice, very silky smooth breakup. It is a classic rock sound that is so much fun to play with. Or you can get really good blues tones out of it. The entire amp is tube powered, down to a tube rectifier and tube reverb.
This amp is better than most other amps I've ever tried. It is durable, reliable, looks and sounds great. If you are on a budget and want to get more than you pay for, at least try this amp. you won't be sorry. If you just take your time with it, you can find a lot of the tones you are looking for. I use a processor in front of it most of the time now, due to the style of playing i have, i need tons of effects. I run that signal into a tube preamp, then into the amp. It sounds wonderful, not at all digital sounding, and is really responsive to nuance. a worthwhile buy for sure.
Pros: sensitive response to playing, great tube sound, built like a tank, enough options for extra cab outputs, and really sweet breakup on the clean channel when turned up allowing for some serious tone.
Cons: no effects loop, trebly (but can be easily remedied by the amps own electronics), heavy as lead to tote (get casters), and cheap stock tubes.
All in all, i don't ever want to be without this amp. I'm sure there are better, but with all the options I have for finding the right sound for a song, i am not even interested in finding one. It does all I need, and what it does not do, I use 3rd party gear to accomplish.

Click Here to see more reviews about: Epiphone Blues Custom Combo Amplifier, 15/30W, Tube 2x12" Speaker

30W or 15W Class AB Combo, Tube Rectifier (5AR4), 2 Channels, DC Powered Filaments, 2 x 12" Eminence Speakers and Tube Reverb

Buy Now

Click here for more information about Epiphone Blues Custom Combo Amplifier, 15/30W, Tube 2x12" Speaker

Read More...

5/04/2012

Fender Blues Junior Hot Rod Series with Optional Amp Cover- Black Review

Fender Blues Junior Hot Rod Series with Optional Amp Cover- Black
Average Reviews:

(More customer reviews)
IF you are looking at getting a Blues Junior, you are basically a stay home practice/player, home recorder, or real small gigger.
Most of the great sounding CRUNCH amps are really meant for large gigs like Hiwatt, Marshall and most Orange's.
Only Orange of those makes a nice crunch in a small amp, but it's not cheap either. Almost 800.
If you want a Blue Junior, you've already decided to get a tube amp and one with EL84s for their crunch, and NOT 6L6 and not an amp for it's amazing CLEAN sound, like say the Fender Reverbs.
Bottom line, this is an amazingly affordable and superb sounding amp at all levels of crunch.
I rate it at a 5 because of it's very reasonable price, especially used. I don't know truly if the newer ones since 2001 are as good as the American made ones, so you'll have to check that out. I don't like these reviews that seem to put all Blues Juniors under one review umbrella when they are different makes at different times, so check out the date info and compare them IF you can. Let your ears determine, not a review or persons opinion.
All I can say is I've searched and played amps for a long time now and I like 6L6 tube amps for clean and EL84's for crunch, all tube and for home non-gigging crunch the Blues Junior is the least expensive best sounding way to go.
As for problems, the main one I've heard is that the tubes don't last as long as other amps, that they are setup to be "hotter". I don't know if this is true, but my attitude is: if that's what it takes to make it sound like this, I LIKE it.
Also, don't get caught up with the "MOD" bug. Yes, there are zillion things you can DO to a Blues Junior. My only advice is, should you want to do this to YOUR amp, let it be your SECOND Blues Junior. If you can't afford a second copy, then don't go messing with the first.
People are always whining about how things don't sound like they did in the 50's. Well, they probably don't remember how while an amp might have sounded superb, the recording technology was in it's infancy and so what they 'heard' on records was a pale shadow. So to sound "like" your favorite Fender amp player, I'm very sure you can make this modern baby sound that bad if you set it up just wrong in the right way.
Good luck, and let your OWN ears, in comparison, sell an amp to you over time.

Click Here to see more reviews about: Fender Blues Junior Hot Rod Series with Optional Amp Cover- Black

The Blues Junior, a warm-toned favorite, takes our 15-watt tube preamp/power amp platform and pushes it through a 12" Fender® Special Design Eminence® speaker. That sound comes courtesy of a pair of EL-84 Groove Tube® output tubes and three 12AX7 preamp tubes. Add our renowned Fender® reverb, flexible controls, and FAT circuit with footswitch for golden tones, and you're in business. And just look at that chrome panel, that black textured vinyl with silver grille cloth, and those vintage pointer knobs.AccessoriesCover :Optional Amp Cover AvailableFootswitch :Uses Optional 1-Button Footswitch, p/n 0994054000ElectronicsChannels :One ChannelControls : Reverb Master Middle Bass Treble "Fat" Switch VolumeEffects : ReverbInputs : OneRectifier : Solid StateCabinet Material :Black Textured Vinyl Covering Front Panel:SilverPilot Light Jewel:Red Amp JewelAmplifier Type :TubeSpeakersSpeaker Impedance :8 OhmsSpeaker :1-12" Fender® Special Design Eminence® 8 ohm, 50 watt SpeakerInput Impedance :1 MPower Handling :15 watts into 8 ohmsPower Tubes :2 x EL84Preamp Tubes : 3 x 12AX7

Buy Now

Click here for more information about Fender Blues Junior Hot Rod Series with Optional Amp Cover- Black

Read More...