Average Reviews:
(More customer reviews)We bought this powered mixer to replace a defective one at our church. Our sanctuary can seat 900 people and so it is a fairly large auditorium. The mixer has more power than the previous powered mixer and many more features. I especially like the individual channel mute buttons so we can kill a mic without having to move the gain adjustments. The only thing I did not like about this mixer is there was no block working diagram available. So we had to construct one for ourselves. To a trained eye, by using a block schematic diagram, it is easier to know how to set up the mixer for different applications and to troubleshoot a problem.
The actual steady state power output is more like 200 watts (each of the two stereo outputs)for our 8 ohm speaker system but still is greater that the old powered mixer. That is a total of 400 watts as compared to the (at first glance) advertised 1200 watts. We do not have to use the maximum gain on any channel so the output is fine for our use. There is also a headset output that follows the actual powered signal which can give you a better idea of mixed signal that is sent to the speakers and to our DVD and CD recorders.
The people at Behringer were able to answer all my questions without any problems so tech support was great. We did have a little difficulty in figuring out how to use the FX special effects (reverb, etc) generator but once we did figure it out, using it was just as advertised. You can probably guess that the instruction manual is not extensively done. But with a limited budget for an emergency purchase of a powered mixer, we are thoroughly satisfied with the quality and price.
The price is exceptional and caused a few doubting comments about how could we get what we needed for such a small price. We have been using the unit for two months now with absolutely no problems.
My suggestion is that before you purchase this unit, download the instruction manual from the Behringer site. You will see the output connection is not a 1/4 jack. If that is what you have, you will have to buy an adapter or convert the present cable connection to the new type. The adapters or connectors are not very expensive (Neutrik NA4LJX Speakon To 1/4" Mono Jack Adapter)and cost under $11 including shipping. You can optionally by the Speakon connectors and convert the speaker cable to the new connector type.
Click Here to see more reviews about: Behringer PMP3000 1,200-Watt 16-Channel Powered Mixer
If you need superior stereo sound for small club gigs, churches or speeches, but have to keep the outboard gear to a minimum, the 16-channel PMP3000 can deliver. This 1,200- Watt mixer has built-in mic preamps and an FX processor, as well as enough power to drive mains and monitors, thanks to dual onboard 600-Watt power amps.
Massive Mono or Stunning Stereo The PMP3000 gives you the choice of 2 x 600-Watt stereo, 2 x 600-Watt dual mono or 1,200-Watt bridged mono sound. Whether the center of attention happens to be a folk trio, a speech, or a synth-rock band with mind-boggling stereo patches, the PMP3000 can accommodate. This sonic versatility also makes it an excellent choice for churches, where vocals and stereo recordings often share face time.
Classic Control, State-of-the-Art Sound Leave the mic preamps at home, because the quality of sound that was once only available in the studio is ready to go wherever you do. Eight built-in, boutique-caliber mic preamps with switchable +48 V phantom power make it possible to use either dynamic or condenser mics with the PMP3000.
Built-in Digital Effects Processor The PMP3000 is also equipped with a 24-bit FX processor, giving you 100 mind-blowing digital effect presets such as delay, chorus and reverb. Apply them to any channel, as well as to the monitors and main output. In case you're pulling double duty as sound engineer and performer, the FX processor features a footswitch jack for remote on/off.
Changing the Channels The PMP3000 gives you excellent flexibility to accommodate whatever a performance requires. Channels 1-8 are for mics, guitars and other mono instruments. Stereo channels 9-16 are ideal for keyboards. All mono channels have 3-band EQ, switchable Low Cut filter for eliminating infrasonics, and Clip LEDs to indicate when the input signal is too hot.
The Ins and Outs Use the CD/TAPE IN RCA inputs to feed in external stereo signals from CD players or tape decks. The VOICE CANCELLER switch eliminates the vocals from pre-recorded music for karaoke applications.
CD/TAPE RCA outputs send line-level signals from the mixer to a recording device. Left and right output 1/4" connectors are there in case you need to connect more power amps. Connect your monitor power amps or active monitor speakers to the MON SEND output.
A STANDBY switch mutes all mic channels during breaks, preventing the microphones from picking up noise or interference. You can leave all faders untouched while you play a CD via the CD/TAPE inputs.
The FBQ Feedback Detection system automatically shows you which frequencies are causing feedback. Just touch the FBQ button and watch the red LEDs on the 7-band graphic EQ pinpoint which frequencies to adjust for optimized sound, without the feedback.
Speaking of Optimized Output The PMP3000's POWER AMP switch toggles between three operating modes: MAIN, MON/MONO and BRIDGE (the power outputs of A and B on the back panel are added and provided at OUTPUT B). Dual mono mode allows you to use Output A for mono Mains and Output B for monitors. This clever functionality powers both your mains and monitors without the need for an additional power amp.
What's in the Box Behringer PMP3000 Powered Mixer, Power Cable, User's Manual
Click here for more information about Behringer PMP3000 1,200-Watt 16-Channel Powered Mixer
No comments:
Post a Comment